IFCONFIG(8) Linux Programmer’s Manual IFCONFIG(8)
名前
ifconfig - ネットワーク・インタフェースの設定
書式
ifconfig [interface]
ifconfig interface [aftype] options | address ...
説明
ifconfig はカーネルによって認識されているネットワーク・インタフェースの
設定に使用する。特にブート時に、必要に応じてインタフェースを設定する た
め に使用される。ブート後には、デバッグやシステムチューニングなどの特殊
な目的がなければ、通常使うことはない。
引数が与えられないと、 ifconfig は現在動作しているインタフェースの状 態
を 表示する。もし一つのインタフェースが引数として与えられると、そのイン
タフェースの状態だけを表示する。また -a が引数として与えられると、停 止
し ているものも含めて、すべてのインタフェースの状態を表示する。以上のい
ずれでもない場合、ifconfig はインタフェースを設定する。
アドレス・ファミリー
インタフェース名の直後に置かれた引数が、サポートされているアドレス・ フ
ァ ミリーの名前として認識されると、すべてのプロトコル・アドレスの解釈と
表示は、そのアドレス・ファミリーに従う。現在サポートされているアドレ ス
・ フ ァミリーは次の通り: inet (TCP/IP, デフォルト), inet6 (IPv6), ax25
(AMPR Pakcet Radio), ddp (Appletalk フェー ズ 2), ipx (Novell IPX),
netrom (AMPR Packet radio).
オプション
interface
インタフェースの名前である。これは通常、ドライバーの名前に装置の
番号を付けたものである。例えば、 eth0 は最初のイーサネット・イン
タフェースである。
up このフラグは、インタフェースを活動状態にする。インタフェースに新
しいアドレスを割り当てた場合は、暗黙のうちにこの up が指定される
。
down このフラグは、このインタフェースのドライバを停止する。
[-]arp ARP プロトコルの使用を有効/無効にする。
[-]promisc
無差別 (promiscuous) モードを有効/無効にする。もし有効にすると、
ネットワーク上のすべてのパケットはこのインタフェースにより受信さ
れる。
[-]allmulti
全マルチキャスト (all-multicast) モードを有効/無効にする。もし有
効にすると、ネットワーク上のすべてのマルチキャスト・パケットはこ
のインタフェースにより受信される。
metric N
この引数はインタフェースメトリックを設定する。
mtu N この引数はインタフェースの最大転送単位 (MTU) を設定する。
dstaddr addr
(PPPのような) ポイント間接続においてリモートの IP アドレスを設定
する。この引数はすでに古い仕様となったので、代り に pointopoint
キーワードを使用すること。
netmask addr
このインタフェースの IP ネットワークマスクを設定する。この値は通
常、 (IP アドレスに対応する) クラス A,B,C の ネットマスクがデ フ
ォルトで設定されるが、値を指定することも可能である。
add addr/prefixlen
IPv6 アドレスをインタフェースに追加する。
del addr/prefixlen
IPv6 アドレスをインタフェースから削除する。
tunnel aa.bb.cc.dd
新規の SIT (IPv6-in-IPv4) デバイスを作成し、与えられた対象アドレ
スにトンネルする。
irq addr
このデバイスにより使用される割り込みを設定する。ただし、すべての
デバイスで動的な IRQ 設定の変更が可能なわけではない。
io_addr addr
このデバイスの I/O 開始アドレスを設定する。
mem_start addr
このデバイスにより使用される共有メモリーの開始アドレスを設定する
。これは、いくつかのデバイスでのみ必要とされる。
media type
このデバイスで使用される、物理ポートもしくは媒体タイプを設定する
。すべてのデバイスで、この設定の変更が可能なわけではない。また可
能なものでも、どの値をサポートしているかはデバイスによって異なる
。 type の値は、 10base2 (thin イーサネット), 10baseT (twisted-
pair 10Mbps イーサネット), AUI (外部トランシーバー) などである。
auto は特殊な媒体指定で、ドライバーに媒体を自動検出するよう伝え
る。同じく、すべてのドライバでこれが可能であるわけではない。
[-]broadcast [addr]
アドレスを指定すると、このインタフェースにプロトコルブロードキャ
ス ト ア ド レスを設定する。指定されないと、このインタフェースに
IFF_BROADCAST フラグを設定 (もしくは解除) する。
[-]pointopoint [addr]
ポイント間接続 (point-to-point) モードを有効にする。これは二つの
マシン間だけで直接接続し、他が干渉できないことを意味する。
アドレスも指定された場合は、リンクの相手側のプロトコルアドレスを
設定する。これにより、 dstaddr は古い仕様となった。指定されな い
場合 IFF_POINTOPOINT フラグを設定もしくは解除するだけである。
hw class address
デバイスドライバーがこの操作をサポートしていれば、インタフェース
のハードウェアアドレスを設定する。このキーワードの後には、ハード
ウ ェアのクラスの名前とハードウェアアドレスにあたる ASCII 文字列
が続かなくてはならない。現在サポートされるハードウェアクラ ス は
ether ( イ ーサネット), ax25 (AMPR AX.25), ARCnet, netrom (AMPR
NET/ROM) である。
multicast
インタフェースのマルチキャストフラグを設定する。通常はドライバー
が自動で設定するので、
address
このインタフェースに割り当てる IP アドレス。
txqueuelen length
デバイスの送信キューの長さをセットする。遅延が大きく、遅いデバイ
ス (モデム、ISDN) に対して小さい値をセットすると、大量転送 中 に
telnet のようなインタラクティブなトラフィックがあまり邪魔されな
いようにできる。
注意
カーネルリリース 2.2 からは、エイリアスされたインタフェースに対する明示
的 なインタフェース統計がなくなった。元のアドレスに対して表示される統計
は、同じデバイスの全ての別名アドレスで共通のものとなる。アドレス毎の 統
計が欲しい場合は、 ipchains(8) コマンドを使って、そのアドレスの明示的な
集計ルールを追加すること。
イーサネットデバイスドライバの割り込み問題により、 EAGAIN で失敗する 。
よ り 詳 細 な 情 報 は http://cesdis.gsfc.nasa.gov/linux/misc/irq-con-
flict.html を参照すること。
ファイル
/proc/net/socket
/proc/net/dev
/proc/net/if_inet6
バグ
Appletalk DDP と IPX はアドレスの表示はするが、このコマンドにより変更す
ることはできない。
関連項目
route(8), netstat(8), arp(8), rarp(8), ipchains(8)
著者
Fred N. van Kempen,
IFCONFIG(8) Linux Programmer’s Manual IFCONFIG(8)
NAME
ifconfig - configure a network interface
SYNOPSIS
ifconfig [interface]
ifconfig interface [aftype] options | address ...
NOTE
This program is obsolete! For replacement check ip addr and ip link.
For statistics use ip -s link.
DESCRIPTION
Ifconfig is used to configure the kernel-resident network interfaces.
It is used at boot time to set up interfaces as necessary. After that,
it is usually only needed when debugging or when system tuning is
needed.
If no arguments are given, ifconfig displays the status of the cur-
rently active interfaces. If a single interface argument is given, it
displays the status of the given interface only; if a single -a argu-
ment is given, it displays the status of all interfaces, even those
that are down. Otherwise, it configures an interface.
Address Families
If the first argument after the interface name is recognized as the
name of a supported address family, that address family is used for
decoding and displaying all protocol addresses. Currently supported
address families include inet (TCP/IP, default), inet6 (IPv6), ax25
(AMPR Packet Radio), ddp (Appletalk Phase 2), ipx (Novell IPX) and
netrom (AMPR Packet radio). All numbers supplied as parts in IPv4 dot-
ted decimal notation may be decimal, octal, or hexadecimal, as speci-
fied in the ISO C standard (that is, a leading 0x or 0X implies hex-
adecimal; otherwise, a leading ’0’ implies octal; otherwise, the number
is interpreted as decimal). Use of hexamedial and octal numbers is not
RFC-compliant and therefore its use is discouraged and may go away.
OPTIONS
interface
The name of the interface. This is usually a driver name fol-
lowed by a unit number, for example eth0 for the first Ethernet
interface.
up This flag causes the interface to be activated. It is implic-
itly specified if an address is assigned to the interface.
down This flag causes the driver for this interface to be shut down.
[-]arp Enable or disable the use of the ARP protocol on this interface.
[-]promisc
Enable or disable the promiscuous mode of the interface. If
selected, all packets on the network will be received by the
interface.
[-]allmulti
Enable or disable all-multicast mode. If selected, all multi-
cast packets on the network will be received by the interface.
metric N
This parameter sets the interface metric. It is not available
under GNU/Linux.
mtu N This parameter sets the Maximum Transfer Unit (MTU) of an inter-
face.
dstaddr addr
Set the remote IP address for a point-to-point link (such as
PPP). This keyword is now obsolete; use the pointopoint keyword
instead.
netmask addr
Set the IP network mask for this interface. This value defaults
to the usual class A, B or C network mask (as derived from the
interface IP address), but it can be set to any value.
add addr/prefixlen
Add an IPv6 address to an interface.
del addr/prefixlen
Remove an IPv6 address from an interface.
tunnel ::aa.bb.cc.dd
Create a new SIT (IPv6-in-IPv4) device, tunnelling to the given
destination.
irq addr
Set the interrupt line used by this device. Not all devices can
dynamically change their IRQ setting.
io_addr addr
Set the start address in I/O space for this device.
mem_start addr
Set the start address for shared memory used by this device.
Only a few devices need this.
media type
Set the physical port or medium type to be used by the device.
Not all devices can change this setting, and those that can vary
in what values they support. Typical values for type are
10base2 (thin Ethernet), 10baseT (twisted-pair 10Mbps Ethernet),
AUI (external transceiver) and so on. The special medium type
of auto can be used to tell the driver to auto-sense the media.
Again, not all drivers can do this.
[-]broadcast [addr]
If the address argument is given, set the protocol broadcast
address for this interface. Otherwise, set (or clear) the
IFF_BROADCAST flag for the interface.
[-]pointopoint [addr]
This keyword enables the point-to-point mode of an interface,
meaning that it is a direct link between two machines with
nobody else listening on it.
If the address argument is also given, set the protocol address
of the other side of the link, just like the obsolete dstaddr
keyword does. Otherwise, set or clear the IFF_POINTOPOINT flag
for the interface.
hw class address
Set the hardware address of this interface, if the device driver
supports this operation. The keyword must be followed by the
name of the hardware class and the printable ASCII equivalent of
the hardware address. Hardware classes currently supported
include ether (Ethernet), ax25 (AMPR AX.25), ARCnet and netrom
(AMPR NET/ROM).
multicast
Set the multicast flag on the interface. This should not nor-
mally be needed as the drivers set the flag correctly them-
selves.
address
The IP address to be assigned to this interface.
txqueuelen length
Set the length of the transmit queue of the device. It is useful
to set this to small values for slower devices with a high
latency (modem links, ISDN) to prevent fast bulk transfers from
disturbing interactive traffic like telnet too much.
NOTES
Since kernel release 2.2 there are no explicit interface statistics for
alias interfaces anymore. The statistics printed for the original
address are shared with all alias addresses on the same device. If you
want per-address statistics you should add explicit accounting rules
for the address using the ipchains(8) command.
Interrupt problems with Ethernet device drivers fail with EAGAIN. See
http://www.scyld.com/expert/irq-conflict.html for more information.
FILES
/proc/net/socket
/proc/net/dev
/proc/net/if_inet6
BUGS
Ifconfig uses obsolete kernel interface. It uses the ioctl access
method to get the full address information, which limits hardware
addresses to 8 bytes. Since an Infiniband address is 20 bytes, only
the first 8 bytes of Infiniband address are displayed.
While appletalk DDP and IPX addresses will be displayed they cannot be
altered by this command.
SEE ALSO
ip(8)
AUTHORS
Fred N. van Kempen,
Copyright(C) linux-cmd.com All Rights Reserved. Author Takayuki Yukawa